Icon Logo Gun Mart

Browning T Bolt

Browning T Bolt

Since Browning launched their resurrected T-Bolt I have been a big fan. Readers might not know that this original, straight-pull rimfire was first introduced in 1965 but discontinued later. Looking quite different the re-vamped gun was back in 2006 with a new 10-shot double helix magazine in 22 Long Rifle. Not long after the first 22 WMR then 17HMR versions appeared.

As a fan of the 17HMR cartridge I was well impressed with these new rifles though thought the barrel a tad long and slim and the synthetic stocked version a bit flexible. My choice would have been the wood furniture, which is more stable. Over the years I have discovered by trial and error that the HMR does not need such a long barrel as I first assumed. This was brought home to me by CZ’s little 16.5” carbine, which gives very little away in terms of ballistics over a 20” tube. So little in fact the handling advantages near outweigh the minimal velocity/energy drop.

SHORT AND RIGID

At this year’s IWA show Browning were showing off yet another version of the T-Bolt, which to me seemed to address most of the questionable areas and also seemed more UK-specific. Called the Target/Varmint, the major differences were a 16.25” heavy barrel as opposed to the usual 22” version and also threaded ½ x 20 UNF. The stock is walnut and certainly more substantial than the black plastic (composite) version. It shows a wide, beavertail-like forend that free-floats the barrel, along with a raised/ambidextrous comb. Chambered in the usual rimfire options the model that spoke to me most was the 17HMR, which is fast becoming the British, small game/vermin hunting calibre.

Six month latter and the new carbine-length Target/Varmint was in my hands and as always I am impressed with this little gun, but this time perhaps even more so as it now seems near built for purpose. Along with it came 100-rounds of the new, Winchester-produced 17HMR, 17-grain ballistic tip ammo. If you read last months’ Return Fire column you will have seen a piece on this calibre and the general drop in ammo quality and reliability.

Winchester tells us that their new HMR round is produced in-house and not by an outside contractor who apparently makes it for everyone else. I was pleased to try this as I too have had some problems with many makes of 17 over the last few years!

THE LOW DOWN

The rifle with its 16.25” barrel is compact and light, being 34.75” long and weighing just 4.9 lbs. The higher comb combined with the long/angled pistol grip and fuller and more rigid forend all come together to offer a comfortable shooting position. As the firing hand makes the hold the trigger finger near automatically makes a ’first pad’ position on the blade. To put it another way – the T-Bolt Sport was good; the Target/Varmint is better!

The muzzle shows a deep, recessed target crown and the chamber is of a semi-match build. It’s threaded ½ x 20 UNF and comes with a protector. Construction is solid with a short, tubular steel receiver, which is drilled and tapped for bases, which are supplied in the box along with a padlock. However the short spacing between the bases does limit scope positioning to a degree. The trigger mech housing (TMH) is all-polymer and shows the magazine release catch at the front of the well. Pulling this literally shoots the mag out, as it’s under spring tension, great but be aware as if you are not it’s easily dropped.

The magazine is a bit different as it uses two, 5-round rotors stacked one above the other (double helix). This makes it the highest capacity, flush-fit unit of any of the 17HMR rifles. Filling is easy as there’s a thumbwheel on the side that allows you to take the spring pressure when loading. Browning only supplies one clip with the rifle, though the Composite version gets two, as it carries a spare in the butt plate.

DOWN, TEST & ADJUST

The trigger blade is gold-plated and easily adjustable via an Allan screw in front of the guard. From the box the pull breaks at an acceptable 4 lbs, but a 5/32” Allen key allows you to fine tune it. Turn clockwise to decrease and clockwise to increase. There’s no creep, just a firm pressurethat breaks cleanly, which is easy to get used to.

story continues below...

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

One of the great features of the T-Bolt is the tang-mounted safety catch, which sits under the firing hand thumb and easily pushes forward to FIRE (red dot exposed). The real beauty is minimal disturbance to your shooting position. It reverses for SAFE and only works when the action is cocked.

The stock is chequered at forend and grip with a nicely aggressive pattern and shows QD sling studs front and back. The length of pull (LOP) is 13.5” and the butt plate is a basic plastic design, I would have preferred a rubber pad here as the issue one slides a bit too easily in the shoulder. Were this my rifle, I’d extend the LOP by at least an inch, which would offer a bit more leeway on eye/scope positioning too.

PUSH PULL

To my knowledge the T-Bolt is now the only straight-pull rimfire rifle in production and the mechanism is simple. The short operating handle sticks out at 90° to the right of the action and shows a flat knob. Pulling it back disengages a cross bolt that locks into both sides of the receiver, operation is a quick pull/push movement. In the bolt channel is a small lug that lies down when the action is cocked and pops up when it’s fired to show gun state. A nice touch is that Browning offer most models in a left hand build too.

So far so good and with my past experience of both 22 LR and 17HMR T-Bolts I was not expecting any dramas either.

For the test I set up an old Weaver/Nitrex 4-20x50 scope (Edgar Brothers) with lockable BDC turrets in Warne mounts. This model has been discontinued but it’s a great piece of glass. Up front an A-Tec CMM rimfire moderator from Jackson Rifles. The test procedure would be zero at 100-yards, check group size and chronograph the load. With my 20” Ruger M77/17 All-Weather I set maximum range at 200-yards and was hoping to see how much difference that 3.75” less of barrel might make.

PUSH!

I found the T-Bolt required more effort on the forward stroke, doubtless this is caused by the striker being set as you close the action. This is less apparent on a traditional turn-bolt as most of this effort is taken up as you close the handle down. None the less with practice it’s fast, with minimal disruption of the firing position!

Average group sizes went to .75”, which is good enough. Out at 200-yards, which is my maximum range in good conditions translates to 1.5-2”, which means a shoulder shot on hares or rabbits is achievable. It should also mean effective head shots at 150-yards too.

I did not have any problems with the new, Winchester-made ammo in terms of reliability or load consistency. However, it appears to be slightly lower powered than the comparable Hornady offering. From the T-Bolt’s 16.25” barrel it was averaging 2449 fps/226 ft/lbs, whereas the Hornady 17 was doing 2505 fps/237 ft/lb. At 200 this drops to 2119 fps/170 ft/lbs and 2171 fps/178 ft/lbs respectively. Not a lot in it and still more than twice the energy of a 22 LR sub-sonic at 100-yards and that can kill rabbits and hares all day long. I would imagine a 20” tube would up the Winchester to around the 2500 fps mark.

Mechanically no dramas - the simple, push/pull bolt action allows for a fast and less interrupted back up shot. Though you do have to be prepared for the extra effort required to close the action, which soon becomes second nature. The shorter barrel as we have seen is no real impediment to down range performance out to what I now consider the 17HMR’s maximum, effective range of 200-yards!

Magazine changes are smooth and easy, as is loading the clip. There is only one potential issue with the generic design and that is the bolt. Though locked to the receiver it can be opened accidently/unknowingly if it were to catch on clothing or even undergrowth. With a turn-bolt system this is not so easy as the lever has first to be lifted up before it can be pulled rearwards. It’s not about safety as the rifle can’t fire out of battery, just something to watch out for!

Overall a sweet, compact and accurate rifle at no real money when compared to guns like the Ruger M77/17 All-Weather and Anschutz 1717 DB, which are now hitting the grand mark.

gun
features

  • Name: Browning T-Bolt Target/Varmint
  • Calibre: 17HMR
  • Barrels: 16.25”
  • Length: 34.75”
  • Weight: 4.9 lbs (un-scoped) Scope bases included

4 Comments

  • Reckon you have, good shooting.

    PM

    Default profile image
    Pete Moore
    12 Oct 2013 at 09:49 AM
  • That was very very good. I've order the target varmint a week a go and after reading this review I feel I've made a good choice. Thank you very much.

    Default profile image
    Patrick Germond
    12 Oct 2013 at 08:53 AM
  • Where did I say standing? I think you have confused 'shoulder shot' as meaning shot from the shoulder. 200 yards shots with the 17HMR are not difficult given there's no wind and you can shoot, but are always taken from a soild/supported firing position - my favourite is off a range bag on the bonnet of my 4x4! Certainly not standing unsupported; you'd have to be Sgt York to do that...

    Default profile image
    PC moore
    02 Sep 2013 at 08:33 AM
  • "Out at 200-yards, which is my maximum range in good conditions translates to 1.5-2”, which means a shoulder shot on hares or rabbits is achievable. It should also mean effective head shots at 150-yards too."

    200 yards standing hitting a 1.5 inch living target? Bull

    Default profile image
    Dan
    30 Aug 2013 at 06:43 PM
  • Thanks for the Reply Pete, that is a great help, i will check them out soon as!!

    thanks,
    Lee

    Default profile image
    Lee Tonks
    21 May 2013 at 05:34 PM
  • Thanks it's a great little rifle. I have not heard from Jager Arms for a long time and am not sure if they are still in business. If you want a good alternative then speak to Third Eye Tactical as they make a reflex rimfire can called the O/B (over barrel). I have just tested it for the July issue of Shooting Sports and it's good.

    The cheekpiece is an Eagle Shooters Stock Pack, which are distributed by Riflecraft, a most practical accessory indeed.

    Cheers
    PM

    Default profile image
    PC moore
    21 May 2013 at 05:29 PM
  • Hi Pete,

    Great review on the T-Bolt, just a quick question!! ive been trying to find out were i cant get the jager arms silencer!! any recomendations on contacts!! also would like to know what brand cheek piece your using there!!

    Thanks,

    Lee

    Default profile image
    Lee Tonks
    21 May 2013 at 05:20 PM
  • Are there any bad things about the t bolt except for the bolt that was mentioned in this review? Thanks

    Default profile image
    Sam
    16 Jul 2012 at 08:43 AM
  • I used two moderators an SAK rimfire/airgun from Jackson Rifles and a Wildcat Growler, which was the first rimfire, reflex can ever made in the UK.

    Default profile image
    pete moore
    26 Mar 2012 at 12:08 PM
  • Hey mate whats the thing on end of your barrel. I want to see if its legal where I am...doubt it though,
    Cheers mate

    Default profile image
    Scott
    23 Mar 2012 at 03:32 PM
  • Bill

    Any competent gunsmith should be able to cut & re-thread the barrel for you. With re-proofing expect to pay £70-100 depending. Best bet is to go to your local gunshop and ask them to order a T-BOLT from the importers BWM Arms Ltd.

    The T-BOLT is a superb little rifle with high accuracy potential. I have one, which was cut-down to 16", which is a practical length for just about any use, with no loss of velocity etc.

    A word of warning though on getting the barrel cut. Not everyone who says they are a gunsmith is and I have seen some horrible cut/re-thread jobs that left the rifle totally inaccurate. With the shop saying it was not them but the rifle and the importers refusing to sort it out under warranty due to the fact it's no longer factory spec.

    If you trust your shop fine, if not I would suggest, take the gun as it comes (22") and shoot it for group and keep the target signed and dated by a reliable witness. This will show what it's capable of, so if it doesn't do it after the modification then you know who to blame...

    Good luck
    PM

    Default profile image
    pete moore
    11 Jan 2010 at 11:02 AM
  • Like the idea of a T-bolt in .22 but want a 16" barrel. Is there anywhere that will stock one or modify it for me?

    Default profile image
    Bill Beaumont
    09 Jan 2010 at 07:07 PM
  • Hi Pate, Just something that I think would be a good addition to the site, if you were to put a link to a page where all the videos can be accessed that would make viewing them much easier, especially if you end up doing more.

    Cheers and thanks for the mag!
    DB

    Default profile image
    Dane Brewer
    17 Dec 2009 at 11:42 AM
  • No arguments from me on that one. The T-Bolt is a cracking little rifle - quick, pointable, slick action and accurate. I'm expecting the 17HMR version soon for testing and will be keen to see how it stacks up against my Ruger 77/17 All-Weather, which is another serious performer.

    PM

    Default profile image
    pete moore
    03 Dec 2009 at 05:44 PM
  • I'm on the other side of the Atlantic and I have to say that I feel sorry for how you guys have to deal with all of the gun laws, but I have a T-bolt and after shooting the cz, I don't think there is really a comparison here. I shot both, but I went with the T-bolt because of accuracy and the way it feels when you put it to your shoulder. It just has something about it when you pick it up and put it to your shoulder. I know this is a personal feeling but, you should definitely test alll of your options out there and see what feels best. For a rifle that you will keep for many years and then pass on to your kids, price should not be a big deal when it comes to quality gun.

    I can say that the browning is definitely a tack driver. I can't tell you how many thousands of rounds I have gone through and how many varmints are gone thanks to this little rifle. I consistently get sub moa groups, if I'm on my game, the rifle will pull 1/2" groups at 100yds with 40g's.

    I have the 22lr version in the standard wood with a Nikon 3x9 40, and I love this little gun.

    Default profile image
    N
    03 Dec 2009 at 05:13 PM
  • Both good rifles no doubt. The 10-shot, flush fit mag and fast action gets my vote, as I have a T-BOLT cut to 16" and it's no problem head-shooting rabbits at 90-yards.

    The CZ 425 is more basic, but in terms of doing the job is equally as efficient and you can get a 10-shot stick mag for it too. Price is perhaps the decider as the T-BOLT will be more expensive by around £100.

    It's your call... I;ve already made mine!

    PM

    Default profile image
    pete moore
    24 Oct 2009 at 06:24 PM
  • was given a shot of one of these at the rifle club at 25 metres put the full 10 rounds through 2 holes on the target very accurate,light andc easy to use this gives me a dillema the browning or the cz when i apply for my section 1 licence

    Default profile image
    sam
    24 Oct 2009 at 05:08 PM


guns for sale

Buy & Sell Online. Advertise your guns and accessories and be seen by 1000’s of buyers..... Buying a Gun or Accessory, Choose from 1000's of items for sale....

Military 1st
Military 1st

Browning T Bolt

Since Browning launched their resurrected T-Bolt I have been a big fan. Readers might not know that this original, straight-pull rimfire was first introduced in 1965 but discontinued later. Looking quite different the re-vamped gun was back in 2006 with a new 10-shot double helix magazine in 22 Long Rifle. Not long after the first 22 WMR then 17HMR versions appeared.

As a fan of the 17HMR cartridge I was well impressed with these new rifles though thought the barrel a tad long and slim and the synthetic stocked version a bit flexible. My choice would have been the wood furniture, which is more stable. Over the years I have discovered by trial and error that the HMR does not need such a long barrel as I first assumed. This was brought home to me by CZ’s little 16.5” carbine, which gives very little away in terms of ballistics over a 20” tube. So little in fact the handling advantages near outweigh the minimal velocity/energy drop.

SHORT AND RIGID

At this year’s IWA show Browning were showing off yet another version of the T-Bolt, which to me seemed to address most of the questionable areas and also seemed more UK-specific. Called the Target/Varmint, the major differences were a 16.25” heavy barrel as opposed to the usual 22” version and also threaded ½ x 20 UNF. The stock is walnut and certainly more substantial than the black plastic (composite) version. It shows a wide, beavertail-like forend that free-floats the barrel, along with a raised/ambidextrous comb. Chambered in the usual rimfire options the model that spoke to me most was the 17HMR, which is fast becoming the British, small game/vermin hunting calibre.

Six month latter and the new carbine-length Target/Varmint was in my hands and as always I am impressed with this little gun, but this time perhaps even more so as it now seems near built for purpose. Along with it came 100-rounds of the new, Winchester-produced 17HMR, 17-grain ballistic tip ammo. If you read last months’ Return Fire column you will have seen a piece on this calibre and the general drop in ammo quality and reliability.

Winchester tells us that their new HMR round is produced in-house and not by an outside contractor who apparently makes it for everyone else. I was pleased to try this as I too have had some problems with many makes of 17 over the last few years!

THE LOW DOWN

The rifle with its 16.25” barrel is compact and light, being 34.75” long and weighing just 4.9 lbs. The higher comb combined with the long/angled pistol grip and fuller and more rigid forend all come together to offer a comfortable shooting position. As the firing hand makes the hold the trigger finger near automatically makes a ’first pad’ position on the blade. To put it another way – the T-Bolt Sport was good; the Target/Varmint is better!

The muzzle shows a deep, recessed target crown and the chamber is of a semi-match build. It’s threaded ½ x 20 UNF and comes with a protector. Construction is solid with a short, tubular steel receiver, which is drilled and tapped for bases, which are supplied in the box along with a padlock. However the short spacing between the bases does limit scope positioning to a degree. The trigger mech housing (TMH) is all-polymer and shows the magazine release catch at the front of the well. Pulling this literally shoots the mag out, as it’s under spring tension, great but be aware as if you are not it’s easily dropped.

The magazine is a bit different as it uses two, 5-round rotors stacked one above the other (double helix). This makes it the highest capacity, flush-fit unit of any of the 17HMR rifles. Filling is easy as there’s a thumbwheel on the side that allows you to take the spring pressure when loading. Browning only supplies one clip with the rifle, though the Composite version gets two, as it carries a spare in the butt plate.

DOWN, TEST & ADJUST

The trigger blade is gold-plated and easily adjustable via an Allan screw in front of the guard. From the box the pull breaks at an acceptable 4 lbs, but a 5/32” Allen key allows you to fine tune it. Turn clockwise to decrease and clockwise to increase. There’s no creep, just a firm pressurethat breaks cleanly, which is easy to get used to.

One of the great features of the T-Bolt is the tang-mounted safety catch, which sits under the firing hand thumb and easily pushes forward to FIRE (red dot exposed). The real beauty is minimal disturbance to your shooting position. It reverses for SAFE and only works when the action is cocked.

The stock is chequered at forend and grip with a nicely aggressive pattern and shows QD sling studs front and back. The length of pull (LOP) is 13.5” and the butt plate is a basic plastic design, I would have preferred a rubber pad here as the issue one slides a bit too easily in the shoulder. Were this my rifle, I’d extend the LOP by at least an inch, which would offer a bit more leeway on eye/scope positioning too.

PUSH PULL

To my knowledge the T-Bolt is now the only straight-pull rimfire rifle in production and the mechanism is simple. The short operating handle sticks out at 90° to the right of the action and shows a flat knob. Pulling it back disengages a cross bolt that locks into both sides of the receiver, operation is a quick pull/push movement. In the bolt channel is a small lug that lies down when the action is cocked and pops up when it’s fired to show gun state. A nice touch is that Browning offer most models in a left hand build too.

So far so good and with my past experience of both 22 LR and 17HMR T-Bolts I was not expecting any dramas either.

For the test I set up an old Weaver/Nitrex 4-20x50 scope (Edgar Brothers) with lockable BDC turrets in Warne mounts. This model has been discontinued but it’s a great piece of glass. Up front an A-Tec CMM rimfire moderator from Jackson Rifles. The test procedure would be zero at 100-yards, check group size and chronograph the load. With my 20” Ruger M77/17 All-Weather I set maximum range at 200-yards and was hoping to see how much difference that 3.75” less of barrel might make.

PUSH!

I found the T-Bolt required more effort on the forward stroke, doubtless this is caused by the striker being set as you close the action. This is less apparent on a traditional turn-bolt as most of this effort is taken up as you close the handle down. None the less with practice it’s fast, with minimal disruption of the firing position!

Average group sizes went to .75”, which is good enough. Out at 200-yards, which is my maximum range in good conditions translates to 1.5-2”, which means a shoulder shot on hares or rabbits is achievable. It should also mean effective head shots at 150-yards too.

I did not have any problems with the new, Winchester-made ammo in terms of reliability or load consistency. However, it appears to be slightly lower powered than the comparable Hornady offering. From the T-Bolt’s 16.25” barrel it was averaging 2449 fps/226 ft/lbs, whereas the Hornady 17 was doing 2505 fps/237 ft/lb. At 200 this drops to 2119 fps/170 ft/lbs and 2171 fps/178 ft/lbs respectively. Not a lot in it and still more than twice the energy of a 22 LR sub-sonic at 100-yards and that can kill rabbits and hares all day long. I would imagine a 20” tube would up the Winchester to around the 2500 fps mark.

Mechanically no dramas - the simple, push/pull bolt action allows for a fast and less interrupted back up shot. Though you do have to be prepared for the extra effort required to close the action, which soon becomes second nature. The shorter barrel as we have seen is no real impediment to down range performance out to what I now consider the 17HMR’s maximum, effective range of 200-yards!

Magazine changes are smooth and easy, as is loading the clip. There is only one potential issue with the generic design and that is the bolt. Though locked to the receiver it can be opened accidently/unknowingly if it were to catch on clothing or even undergrowth. With a turn-bolt system this is not so easy as the lever has first to be lifted up before it can be pulled rearwards. It’s not about safety as the rifle can’t fire out of battery, just something to watch out for!

Overall a sweet, compact and accurate rifle at no real money when compared to guns like the Ruger M77/17 All-Weather and Anschutz 1717 DB, which are now hitting the grand mark.

Comments

  • Reckon you have, good shooting.

    PM

    Default profile image
    Pete Moore
    12 Oct 2013 at 09:49 AM
  • That was very very good. I've order the target varmint a week a go and after reading this review I feel I've made a good choice. Thank you very much.

    Default profile image
    Patrick Germond
    12 Oct 2013 at 08:53 AM
  • Where did I say standing? I think you have confused 'shoulder shot' as meaning shot from the shoulder. 200 yards shots with the 17HMR are not difficult given there's no wind and you can shoot, but are always taken from a soild/supported firing position - my favourite is off a range bag on the bonnet of my 4x4! Certainly not standing unsupported; you'd have to be Sgt York to do that...

    Default profile image
    PC moore
    02 Sep 2013 at 08:33 AM
  • "Out at 200-yards, which is my maximum range in good conditions translates to 1.5-2”, which means a shoulder shot on hares or rabbits is achievable. It should also mean effective head shots at 150-yards too."

    200 yards standing hitting a 1.5 inch living target? Bull

    Default profile image
    Dan
    30 Aug 2013 at 06:43 PM
  • Thanks for the Reply Pete, that is a great help, i will check them out soon as!!

    thanks,
    Lee

    Default profile image
    Lee Tonks
    21 May 2013 at 05:34 PM
  • Thanks it's a great little rifle. I have not heard from Jager Arms for a long time and am not sure if they are still in business. If you want a good alternative then speak to Third Eye Tactical as they make a reflex rimfire can called the O/B (over barrel). I have just tested it for the July issue of Shooting Sports and it's good.

    The cheekpiece is an Eagle Shooters Stock Pack, which are distributed by Riflecraft, a most practical accessory indeed.

    Cheers
    PM

    Default profile image
    PC moore
    21 May 2013 at 05:29 PM
  • Hi Pete,

    Great review on the T-Bolt, just a quick question!! ive been trying to find out were i cant get the jager arms silencer!! any recomendations on contacts!! also would like to know what brand cheek piece your using there!!

    Thanks,

    Lee

    Default profile image
    Lee Tonks
    21 May 2013 at 05:20 PM
  • Are there any bad things about the t bolt except for the bolt that was mentioned in this review? Thanks

    Default profile image
    Sam
    16 Jul 2012 at 08:43 AM
  • I used two moderators an SAK rimfire/airgun from Jackson Rifles and a Wildcat Growler, which was the first rimfire, reflex can ever made in the UK.

    Default profile image
    pete moore
    26 Mar 2012 at 12:08 PM
  • Hey mate whats the thing on end of your barrel. I want to see if its legal where I am...doubt it though,
    Cheers mate

    Default profile image
    Scott
    23 Mar 2012 at 03:32 PM
  • Bill

    Any competent gunsmith should be able to cut & re-thread the barrel for you. With re-proofing expect to pay £70-100 depending. Best bet is to go to your local gunshop and ask them to order a T-BOLT from the importers BWM Arms Ltd.

    The T-BOLT is a superb little rifle with high accuracy potential. I have one, which was cut-down to 16", which is a practical length for just about any use, with no loss of velocity etc.

    A word of warning though on getting the barrel cut. Not everyone who says they are a gunsmith is and I have seen some horrible cut/re-thread jobs that left the rifle totally inaccurate. With the shop saying it was not them but the rifle and the importers refusing to sort it out under warranty due to the fact it's no longer factory spec.

    If you trust your shop fine, if not I would suggest, take the gun as it comes (22") and shoot it for group and keep the target signed and dated by a reliable witness. This will show what it's capable of, so if it doesn't do it after the modification then you know who to blame...

    Good luck
    PM

    Default profile image
    pete moore
    11 Jan 2010 at 11:02 AM
  • Like the idea of a T-bolt in .22 but want a 16" barrel. Is there anywhere that will stock one or modify it for me?

    Default profile image
    Bill Beaumont
    09 Jan 2010 at 07:07 PM
  • Hi Pate, Just something that I think would be a good addition to the site, if you were to put a link to a page where all the videos can be accessed that would make viewing them much easier, especially if you end up doing more.

    Cheers and thanks for the mag!
    DB

    Default profile image
    Dane Brewer
    17 Dec 2009 at 11:42 AM
  • No arguments from me on that one. The T-Bolt is a cracking little rifle - quick, pointable, slick action and accurate. I'm expecting the 17HMR version soon for testing and will be keen to see how it stacks up against my Ruger 77/17 All-Weather, which is another serious performer.

    PM

    Default profile image
    pete moore
    03 Dec 2009 at 05:44 PM
  • I'm on the other side of the Atlantic and I have to say that I feel sorry for how you guys have to deal with all of the gun laws, but I have a T-bolt and after shooting the cz, I don't think there is really a comparison here. I shot both, but I went with the T-bolt because of accuracy and the way it feels when you put it to your shoulder. It just has something about it when you pick it up and put it to your shoulder. I know this is a personal feeling but, you should definitely test alll of your options out there and see what feels best. For a rifle that you will keep for many years and then pass on to your kids, price should not be a big deal when it comes to quality gun.

    I can say that the browning is definitely a tack driver. I can't tell you how many thousands of rounds I have gone through and how many varmints are gone thanks to this little rifle. I consistently get sub moa groups, if I'm on my game, the rifle will pull 1/2" groups at 100yds with 40g's.

    I have the 22lr version in the standard wood with a Nikon 3x9 40, and I love this little gun.

    Default profile image
    N
    03 Dec 2009 at 05:13 PM
  • Both good rifles no doubt. The 10-shot, flush fit mag and fast action gets my vote, as I have a T-BOLT cut to 16" and it's no problem head-shooting rabbits at 90-yards.

    The CZ 425 is more basic, but in terms of doing the job is equally as efficient and you can get a 10-shot stick mag for it too. Price is perhaps the decider as the T-BOLT will be more expensive by around £100.

    It's your call... I;ve already made mine!

    PM

    Default profile image
    pete moore
    24 Oct 2009 at 06:24 PM
  • was given a shot of one of these at the rifle club at 25 metres put the full 10 rounds through 2 holes on the target very accurate,light andc easy to use this gives me a dillema the browning or the cz when i apply for my section 1 licence

    Default profile image
    sam
    24 Oct 2009 at 05:08 PM


More Video ReviewsView All >

ad
guns for sale

Buy & Sell Online. Advertise your guns and accessories and be seen by 1000’s of buyers..... Buying a Gun or Accessory, Choose from 1000's of items for sale....

Military 1st
Military 1st

Browning T Bolt

Browning T Bolt

Since Browning launched their resurrected T-Bolt I have been a big fan. Readers might not know that this original, straight-pull rimfire was first introduced in 1965 but discontinued later. Looking quite different the re-vamped gun was back in 2006 with a new 10-shot double helix magazine in 22 Long Rifle. Not long after the first 22 WMR then 17HMR versions appeared.

As a fan of the 17HMR cartridge I was well impressed with these new rifles though thought the barrel a tad long and slim and the synthetic stocked version a bit flexible. My choice would have been the wood furniture, which is more stable. Over the years I have discovered by trial and error that the HMR does not need such a long barrel as I first assumed. This was brought home to me by CZ’s little 16.5” carbine, which gives very little away in terms of ballistics over a 20” tube. So little in fact the handling advantages near outweigh the minimal velocity/energy drop.

SHORT AND RIGID

At this year’s IWA show Browning were showing off yet another version of the T-Bolt, which to me seemed to address most of the questionable areas and also seemed more UK-specific. Called the Target/Varmint, the major differences were a 16.25” heavy barrel as opposed to the usual 22” version and also threaded ½ x 20 UNF. The stock is walnut and certainly more substantial than the black plastic (composite) version. It shows a wide, beavertail-like forend that free-floats the barrel, along with a raised/ambidextrous comb. Chambered in the usual rimfire options the model that spoke to me most was the 17HMR, which is fast becoming the British, small game/vermin hunting calibre.

Six month latter and the new carbine-length Target/Varmint was in my hands and as always I am impressed with this little gun, but this time perhaps even more so as it now seems near built for purpose. Along with it came 100-rounds of the new, Winchester-produced 17HMR, 17-grain ballistic tip ammo. If you read last months’ Return Fire column you will have seen a piece on this calibre and the general drop in ammo quality and reliability.

Winchester tells us that their new HMR round is produced in-house and not by an outside contractor who apparently makes it for everyone else. I was pleased to try this as I too have had some problems with many makes of 17 over the last few years!

THE LOW DOWN

The rifle with its 16.25” barrel is compact and light, being 34.75” long and weighing just 4.9 lbs. The higher comb combined with the long/angled pistol grip and fuller and more rigid forend all come together to offer a comfortable shooting position. As the firing hand makes the hold the trigger finger near automatically makes a ’first pad’ position on the blade. To put it another way – the T-Bolt Sport was good; the Target/Varmint is better!

The muzzle shows a deep, recessed target crown and the chamber is of a semi-match build. It’s threaded ½ x 20 UNF and comes with a protector. Construction is solid with a short, tubular steel receiver, which is drilled and tapped for bases, which are supplied in the box along with a padlock. However the short spacing between the bases does limit scope positioning to a degree. The trigger mech housing (TMH) is all-polymer and shows the magazine release catch at the front of the well. Pulling this literally shoots the mag out, as it’s under spring tension, great but be aware as if you are not it’s easily dropped.

The magazine is a bit different as it uses two, 5-round rotors stacked one above the other (double helix). This makes it the highest capacity, flush-fit unit of any of the 17HMR rifles. Filling is easy as there’s a thumbwheel on the side that allows you to take the spring pressure when loading. Browning only supplies one clip with the rifle, though the Composite version gets two, as it carries a spare in the butt plate.

DOWN, TEST & ADJUST

The trigger blade is gold-plated and easily adjustable via an Allan screw in front of the guard. From the box the pull breaks at an acceptable 4 lbs, but a 5/32” Allen key allows you to fine tune it. Turn clockwise to decrease and clockwise to increase. There’s no creep, just a firm pressurethat breaks cleanly, which is easy to get used to.

story continues below...

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

  • Browning T Bolt - image {image:count}

    click on image to enlarge

One of the great features of the T-Bolt is the tang-mounted safety catch, which sits under the firing hand thumb and easily pushes forward to FIRE (red dot exposed). The real beauty is minimal disturbance to your shooting position. It reverses for SAFE and only works when the action is cocked.

The stock is chequered at forend and grip with a nicely aggressive pattern and shows QD sling studs front and back. The length of pull (LOP) is 13.5” and the butt plate is a basic plastic design, I would have preferred a rubber pad here as the issue one slides a bit too easily in the shoulder. Were this my rifle, I’d extend the LOP by at least an inch, which would offer a bit more leeway on eye/scope positioning too.

PUSH PULL

To my knowledge the T-Bolt is now the only straight-pull rimfire rifle in production and the mechanism is simple. The short operating handle sticks out at 90° to the right of the action and shows a flat knob. Pulling it back disengages a cross bolt that locks into both sides of the receiver, operation is a quick pull/push movement. In the bolt channel is a small lug that lies down when the action is cocked and pops up when it’s fired to show gun state. A nice touch is that Browning offer most models in a left hand build too.

So far so good and with my past experience of both 22 LR and 17HMR T-Bolts I was not expecting any dramas either.

For the test I set up an old Weaver/Nitrex 4-20x50 scope (Edgar Brothers) with lockable BDC turrets in Warne mounts. This model has been discontinued but it’s a great piece of glass. Up front an A-Tec CMM rimfire moderator from Jackson Rifles. The test procedure would be zero at 100-yards, check group size and chronograph the load. With my 20” Ruger M77/17 All-Weather I set maximum range at 200-yards and was hoping to see how much difference that 3.75” less of barrel might make.

PUSH!

I found the T-Bolt required more effort on the forward stroke, doubtless this is caused by the striker being set as you close the action. This is less apparent on a traditional turn-bolt as most of this effort is taken up as you close the handle down. None the less with practice it’s fast, with minimal disruption of the firing position!

Average group sizes went to .75”, which is good enough. Out at 200-yards, which is my maximum range in good conditions translates to 1.5-2”, which means a shoulder shot on hares or rabbits is achievable. It should also mean effective head shots at 150-yards too.

I did not have any problems with the new, Winchester-made ammo in terms of reliability or load consistency. However, it appears to be slightly lower powered than the comparable Hornady offering. From the T-Bolt’s 16.25” barrel it was averaging 2449 fps/226 ft/lbs, whereas the Hornady 17 was doing 2505 fps/237 ft/lb. At 200 this drops to 2119 fps/170 ft/lbs and 2171 fps/178 ft/lbs respectively. Not a lot in it and still more than twice the energy of a 22 LR sub-sonic at 100-yards and that can kill rabbits and hares all day long. I would imagine a 20” tube would up the Winchester to around the 2500 fps mark.

Mechanically no dramas - the simple, push/pull bolt action allows for a fast and less interrupted back up shot. Though you do have to be prepared for the extra effort required to close the action, which soon becomes second nature. The shorter barrel as we have seen is no real impediment to down range performance out to what I now consider the 17HMR’s maximum, effective range of 200-yards!

Magazine changes are smooth and easy, as is loading the clip. There is only one potential issue with the generic design and that is the bolt. Though locked to the receiver it can be opened accidently/unknowingly if it were to catch on clothing or even undergrowth. With a turn-bolt system this is not so easy as the lever has first to be lifted up before it can be pulled rearwards. It’s not about safety as the rifle can’t fire out of battery, just something to watch out for!

Overall a sweet, compact and accurate rifle at no real money when compared to guns like the Ruger M77/17 All-Weather and Anschutz 1717 DB, which are now hitting the grand mark.

gun
features

  • Name: Browning T-Bolt Target/Varmint
  • Calibre: 17HMR
  • Barrels: 16.25”
  • Length: 34.75”
  • Weight: 4.9 lbs (un-scoped) Scope bases included

4 Comments

  • Reckon you have, good shooting.

    PM

    Default profile image
    Pete Moore
    12 Oct 2013 at 09:49 AM
  • That was very very good. I've order the target varmint a week a go and after reading this review I feel I've made a good choice. Thank you very much.

    Default profile image
    Patrick Germond
    12 Oct 2013 at 08:53 AM
  • Where did I say standing? I think you have confused 'shoulder shot' as meaning shot from the shoulder. 200 yards shots with the 17HMR are not difficult given there's no wind and you can shoot, but are always taken from a soild/supported firing position - my favourite is off a range bag on the bonnet of my 4x4! Certainly not standing unsupported; you'd have to be Sgt York to do that...

    Default profile image
    PC moore
    02 Sep 2013 at 08:33 AM
  • "Out at 200-yards, which is my maximum range in good conditions translates to 1.5-2”, which means a shoulder shot on hares or rabbits is achievable. It should also mean effective head shots at 150-yards too."

    200 yards standing hitting a 1.5 inch living target? Bull

    Default profile image
    Dan
    30 Aug 2013 at 06:43 PM
  • Thanks for the Reply Pete, that is a great help, i will check them out soon as!!

    thanks,
    Lee

    Default profile image
    Lee Tonks
    21 May 2013 at 05:34 PM
  • Thanks it's a great little rifle. I have not heard from Jager Arms for a long time and am not sure if they are still in business. If you want a good alternative then speak to Third Eye Tactical as they make a reflex rimfire can called the O/B (over barrel). I have just tested it for the July issue of Shooting Sports and it's good.

    The cheekpiece is an Eagle Shooters Stock Pack, which are distributed by Riflecraft, a most practical accessory indeed.

    Cheers
    PM

    Default profile image
    PC moore
    21 May 2013 at 05:29 PM
  • Hi Pete,

    Great review on the T-Bolt, just a quick question!! ive been trying to find out were i cant get the jager arms silencer!! any recomendations on contacts!! also would like to know what brand cheek piece your using there!!

    Thanks,

    Lee

    Default profile image
    Lee Tonks
    21 May 2013 at 05:20 PM
  • Are there any bad things about the t bolt except for the bolt that was mentioned in this review? Thanks

    Default profile image
    Sam
    16 Jul 2012 at 08:43 AM
  • I used two moderators an SAK rimfire/airgun from Jackson Rifles and a Wildcat Growler, which was the first rimfire, reflex can ever made in the UK.

    Default profile image
    pete moore
    26 Mar 2012 at 12:08 PM
  • Hey mate whats the thing on end of your barrel. I want to see if its legal where I am...doubt it though,
    Cheers mate

    Default profile image
    Scott
    23 Mar 2012 at 03:32 PM
  • Bill

    Any competent gunsmith should be able to cut & re-thread the barrel for you. With re-proofing expect to pay £70-100 depending. Best bet is to go to your local gunshop and ask them to order a T-BOLT from the importers BWM Arms Ltd.

    The T-BOLT is a superb little rifle with high accuracy potential. I have one, which was cut-down to 16", which is a practical length for just about any use, with no loss of velocity etc.

    A word of warning though on getting the barrel cut. Not everyone who says they are a gunsmith is and I have seen some horrible cut/re-thread jobs that left the rifle totally inaccurate. With the shop saying it was not them but the rifle and the importers refusing to sort it out under warranty due to the fact it's no longer factory spec.

    If you trust your shop fine, if not I would suggest, take the gun as it comes (22") and shoot it for group and keep the target signed and dated by a reliable witness. This will show what it's capable of, so if it doesn't do it after the modification then you know who to blame...

    Good luck
    PM

    Default profile image
    pete moore
    11 Jan 2010 at 11:02 AM
  • Like the idea of a T-bolt in .22 but want a 16" barrel. Is there anywhere that will stock one or modify it for me?

    Default profile image
    Bill Beaumont
    09 Jan 2010 at 07:07 PM
  • Hi Pate, Just something that I think would be a good addition to the site, if you were to put a link to a page where all the videos can be accessed that would make viewing them much easier, especially if you end up doing more.

    Cheers and thanks for the mag!
    DB

    Default profile image
    Dane Brewer
    17 Dec 2009 at 11:42 AM
  • No arguments from me on that one. The T-Bolt is a cracking little rifle - quick, pointable, slick action and accurate. I'm expecting the 17HMR version soon for testing and will be keen to see how it stacks up against my Ruger 77/17 All-Weather, which is another serious performer.

    PM

    Default profile image
    pete moore
    03 Dec 2009 at 05:44 PM
  • I'm on the other side of the Atlantic and I have to say that I feel sorry for how you guys have to deal with all of the gun laws, but I have a T-bolt and after shooting the cz, I don't think there is really a comparison here. I shot both, but I went with the T-bolt because of accuracy and the way it feels when you put it to your shoulder. It just has something about it when you pick it up and put it to your shoulder. I know this is a personal feeling but, you should definitely test alll of your options out there and see what feels best. For a rifle that you will keep for many years and then pass on to your kids, price should not be a big deal when it comes to quality gun.

    I can say that the browning is definitely a tack driver. I can't tell you how many thousands of rounds I have gone through and how many varmints are gone thanks to this little rifle. I consistently get sub moa groups, if I'm on my game, the rifle will pull 1/2" groups at 100yds with 40g's.

    I have the 22lr version in the standard wood with a Nikon 3x9 40, and I love this little gun.

    Default profile image
    N
    03 Dec 2009 at 05:13 PM
  • Both good rifles no doubt. The 10-shot, flush fit mag and fast action gets my vote, as I have a T-BOLT cut to 16" and it's no problem head-shooting rabbits at 90-yards.

    The CZ 425 is more basic, but in terms of doing the job is equally as efficient and you can get a 10-shot stick mag for it too. Price is perhaps the decider as the T-BOLT will be more expensive by around £100.

    It's your call... I;ve already made mine!

    PM

    Default profile image
    pete moore
    24 Oct 2009 at 06:24 PM
  • was given a shot of one of these at the rifle club at 25 metres put the full 10 rounds through 2 holes on the target very accurate,light andc easy to use this gives me a dillema the browning or the cz when i apply for my section 1 licence

    Default profile image
    sam
    24 Oct 2009 at 05:08 PM


guns for sale

Buy & Sell Online. Advertise your guns and accessories and be seen by 1000’s of buyers..... Buying a Gun or Accessory, Choose from 1000's of items for sale....

Military 1st
Military 1st
Arrow
Close button

FREE

NIGHT VISION DOWNLOAD

Terms and conditions apply, click through for details